Forum Replies Created

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • January 4, 2014 at 6:05 pm in reply to: Fibreglass Master Craftman wanted #11890
    TonyB
    Member

    Cheers Steve:
    you are a veritable Diamond of a Chap !!
    Tony

    January 3, 2014 at 6:15 pm in reply to: RC Owners manual #11884
    TonyB
    Member

    Hi Trev,
    Many many thanks for the CD ..
    However there is nothing on it Mate…
    when I open it it says no items to view

    thanks for the effort though
    cheers
    Tony

    December 31, 2013 at 8:54 am in reply to: seat unit metal brackets + infos #11875
    TonyB
    Member

    Hi Steve,
    this is my idea/tghoughts
    Comments please>>>>>>>

    Ok .. the challenge !
    I need to fit the seat /side panel unit from my Harris replicxa CB1100R to my CB1100FD Bol dOr.
    I/we have sorted the Tank
    in order to fit the Seat/side oanel unit we /I need 3 brackets making either side like the ones attached in the pictures below.
    My idea was to fabricate 4 of he brackets as shown ( LHS & RHS) BUT where the upper & lower arms of the bracket are welded to the frame on a CB1100R…. for the purposes of fitting the brackets to the CB1100FD frame the upper & lower arms of the bracket have a semi circular piece of tube welded to the upper & lower arms, the profile of the semi circular piece will be slightly greater in diameter than the frame tube that it will attached to.
    The frame brackets will then have a semi circular piece of rubber inserted around the back of them which is liuke a spacer than will fit around the original frame tube.
    The bracket will be held in place by two stainless steel jubilee clips per bracket.
    so that there will be no welding to the frame.
    The two brackets at the rear of the frame are easy to make ( I think for you.. but not for me !!!!)
    Well that is the challenge!
    What do you think?
    Cheers
    Tony

    December 28, 2013 at 11:57 am in reply to: seat unit metal brackets + infos #11868
    TonyB
    Member

    Cheers Andy,
    Just need a good fabricator now!.. any recommendations?
    Cheers
    Tony

    December 28, 2013 at 11:56 am in reply to: EBay Watch – Bikes for sale #11867
    TonyB
    Member

    Steve:#
    he quoted me £300 from Holland to England, & £350 for Scotland.
    HTH
    Cheers
    Tony

    December 26, 2013 at 3:21 pm in reply to: seat unit metal brackets + infos #11862
    TonyB
    Member

    Andy:
    Any chance of the same pics and the drawing Mate?
    Cheers
    Tony
    aabaillie@yahoo.co.uk

    December 26, 2013 at 3:17 pm in reply to: EBay Watch – Bikes for sale #11861
    TonyB
    Member

    Steve:
    contact Chas Mortimer he is the best and cheapest guy around for bike pick-up & delivery to the UK from Europe.
    Cheers
    Tony

    December 15, 2013 at 6:25 pm in reply to: RC Owners manual #11847
    TonyB
    Member

    Hi Trev,
    many many thanks for that IT REALLY IS MOST APPRECIATED !
    my address as follows:

    TONY BAILEY
    “CRAIGINFINNY”
    MULL
    DRUMMORE
    STRANRAER
    WIGTOWNSHIRE
    DG9 9HR
    SCOTLAND

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)